Specification Guide — Process Equipment

Pressure Vessel vs. Tank vs. Reactor
How to Specify the Right System

These three categories are not interchangeable labels. Each reflects a different set of engineering priorities, code requirements, and design decisions. Selecting the wrong category early — or treating them as equivalent options — leads to specifications that don't match the application and equipment that doesn't do the job.

Start with the Process, Not the Equipment

The right category for a piece of process equipment is determined by what that equipment must do — not by its size, shape, or material. A vessel that holds 1,000 gallons under atmospheric pressure for product storage is a tank. A vessel that holds 1,000 gallons under 150 PSI for pharmaceutical product processing is a pressure vessel. A vessel that holds 1,000 gallons under 150 PSI while managing temperature, agitation, dosing sequence, and reaction conditions is a reactor.

The distinction matters because it determines what engineering questions need to be answered, which codes apply, what documentation is required, and what the fabricator must be capable of delivering. Starting from the process — not from a size or shape assumption — is how to get to the right specification.

Pressure Vessel

Designed around operating conditions — pressure, temperature, vacuum, containment. Engineering starts with what the vessel must contain and withstand.

Process Tank

Designed around workflow — storage, blending, buffering, transfer. Engineering starts with volume, geometry, drainability, and access.

Reactor

Designed around the process outcome — what happens inside determines the design priorities. Engineering starts with the process itself.

Side-by-Side Comparison

How design priorities, code requirements, and engineering focus differ across the three categories.

DimensionPressure VesselProcess TankReactor
Primary Design DriverOperating conditions — pressure, temperature, vacuum, containment integrityProcess workflow — storage, buffering, transfer, blending at near-atmospheric conditionsProcess outcome — what happens inside determines the design priorities
Code ApplicabilityASME BPVC Section VIII typically required above jurisdictional thresholds; U or UM stampMay be exempt from ASME requirements depending on conditions; verify with AHJ and insurerASME Section VIII where pressure-retaining; additional codes may apply for regulated applications
Interior Engineering FocusStructural integrity, pressure containment, material compatibility, NDEVolume, drainability, access, cleaning, sanitary geometry where applicableProcess control — agitation, thermal management, dosing, residence time, phase behavior
Thermal Management RoleMay carry jacketing for heating or cooling; thermal design is secondary to containmentOften minimal — temperature maintenance or simple jacketed heatingOften primary — temperature control, ramp rate, hold stability shape process outcomes
Agitation / MixingNot always present; may have baffles or mixers depending on processCommon — blending, slurry maintenance, suspensionTypically central — agitation design drives uniformity, shear exposure, and reaction behavior
Hygienic / CIP DesignRequired when application demands it; geometry and finish defined by industry standardCommon in food, beverage, pharma; designed for spray coverage and drainabilityRequired in pharma, biopharma, bioprocessing; full CIP/SIP engineering built into design
Automation ComplexityBasic monitoring and control typical; pressure relief and interlock logicModerate — level, temperature, fill/drain sequencesOften high — sequencing, recipe control, alarms, interlocks, operator interface, SCADA
Documentation DepthASME data report, MTRs, AI review; deeper for regulated industriesLighter for non-coded tanks; food/pharma applications require material and surface finish recordsFull project documentation; design rationale, thermal analysis, validation-ready packages for regulated use
Typical IndustriesChemical processing, oil and gas, pharma, food/beverage, thermal systems, semiconductorFood and beverage, water treatment, chemical storage, general industrial, dairyPharma, biopharma, chemical synthesis, specialty processing, food (batch reactors), research

What to Clarify Before the RFQ

Regardless of which category applies, these items must be defined before fabrication can begin. Missing any of them leads to either underspec'd equipment or unnecessary scope creep.

Define what happens inside the vessel

Is material simply being stored and moved, or is the vessel actively managing a process — reaction, mixing sequence, temperature control, or dosing? This answer determines the design category.

Establish operating conditions fully

Pressure, temperature, vacuum, cyclic service, and hold requirements must be defined before design begins. Missing any of these leads to underspec'd equipment.

Clarify code applicability early

Determine whether ASME Section VIII applies before writing the RFQ. Confirm with your engineer and jurisdictional authority — do not assume exempt.

Define the cleaning strategy

CIP vs. manual cleaning vs. no cleaning requirement must be established before internal geometry is designed. CIP-ready design must be built in from the start.

Identify thermal requirements explicitly

If temperature control matters to the process, treat thermal design as a primary design driver — not a secondary consideration. Define ramp rates, hold stability, and thermal duty from the beginning.

Specify automation intent

Automation affects nozzle placement, instrumentation, controls architecture, and project budget. Define automation requirements before detailed engineering begins.

State regulatory and documentation expectations

Regulated applications require documentation packages. Define expected deliverables — MTRs, surface finish records, validation-ready documentation — before quoting.

Frequently Asked Questions

Need Help Classifying Your Application?

MRX designs and fabricates pressure vessels, process tanks, and reactor systems for pharma, food, beverage, specialty processing, and industrial applications. Talk to our team about your process requirements.