Home/Resources/RFQ Checklist
← Full Buyer's Guide
M
MRX Manufacturing · Canby, Oregon

Pressure Vessel RFQ Preparation Checklist

Use this checklist to prepare a complete, code-accurate RFQ for custom ASME pressure vessels, jacketed reactors, and specialty containers.

mrxmfg.com

info@mrxmfg.com

2026 Edition

Why this matters: An incomplete RFQ produces bids that are either padded with contingency or structurally non-comparable. Specifying design pressure, applicable code, material, NDE scope, and documentation requirements upfront eliminates the most common causes of bid spread and post-award change orders.

1. Applicable Code & Certification

ASME code: Section VIII Division 1 / Division 2 / Section III (specify which applies)

ASME stamp required: U stamp / U2 stamp / N stamp / none (specify)

Canadian Registration Number (CRN) required — list provinces

State/jurisdictional registration requirements (list states if applicable)

Third-party inspection required — specify Authorized Inspection Agency (AIA)

National Board registration required (NB stamp on nameplate)

2. Design Conditions

Design pressure (internal): ___ psig

Design pressure (external/full vacuum): Yes / No

Design temperature (maximum operating): ___ °F

Design temperature (minimum): ___ °F (for low-temperature or cryogenic service)

Hydrotest or pneumatic test pressure: ___ psig (if deviation from code default required)

Radiography category: Full / Spot / None (specify per joint)

3. Fluid & Service

Fluid(s) in contact with vessel internals (name each, including cleaning agents)

Fluid phase: liquid / gas / two-phase

Corrosive, toxic, or lethal service: Yes / No (if yes, specify)

Hydrogen service or other specialized environment: Yes / No

Cyclic pressure or thermal cycling service: Yes / No

4. Materials

Shell and head material (specify SA designation if known, e.g. SA-516-70)

Nozzle and flange material

Internals material (baffles, supports, trays, agitator, coils)

Weld filler material requirements or restrictions

Impact testing required: Yes / No — if yes, specify MDMT

Mill certifications required: Yes / No — EN 10204 Type 3.1 or 3.2

5. Vessel Geometry

Shell inside diameter (ID): ___ inches

Shell nominal length / tangent-to-tangent length: ___ inches

Head type: 2:1 ellipsoidal / hemispherical / ASME F&D / flat (specify top and bottom)

Orientation: vertical / horizontal (specify support type: legs, saddles, lugs)

Number of nozzles — list each: size, rating (ANSI 150/300/600), facing (RF/FF/RTJ), orientation

Manway required: Yes / No — if yes: size, orientation, hinge or davit

6. Internals & Special Features

Agitator/mixer: Yes / No — if yes: type, speed, shaft seal type

Heating/cooling jacket: Yes / No — if yes: type (conventional, dimple, half-pipe), design pressure

Internal coils: Yes / No — if yes: material, design pressure, coil geometry

Internal lining (glass, rubber, PTFE, Hastelloy, etc.): Yes / No

Removable or cleanable internals required: Yes / No

Spray nozzles or CIP spray balls: Yes / No — specify flow requirement

7. Surface Finish & Cleanliness

External finish: mill / sandblast / primer / paint (specify RAL/color if applicable)

Internal finish: mill / #4 polish / #4 electropolish / specify Ra ≤ ___ µin

Passivation required: Yes / No — specify standard (ASTM A967 citric or nitric)

Electropolish required: Yes / No — specify Ra requirement (e.g. ≤ 20 µin / ≤ 0.5 µm)

Sanitary/hygienic construction (3-A, ASME BPE): specify applicable standard

Product contact surface documentation (certificates, profilometry reports): Yes / No

8. Non-Destructive Examination (NDE)

Radiography (RT): per code minimum / spot / full / none (specify joints)

Ultrasonic testing (UT): Yes / No — specify scope

Magnetic particle (MT) or liquid penetrant (PT): Yes / No — specify scope

Post-weld heat treatment (PWHT): per code / required / waived — specify basis

Charpy impact testing: per code / required — specify minimum temperature

Hardness testing required: Yes / No

9. Documentation Package

ASME U1 or U1A data report (mandatory for U-stamped vessels)

Material certifications (MTRs) — specify retention requirement

Weld procedure specifications (WPS) and procedure qualification records (PQR)

Weld map and weld traveler

NDE reports (RT film, UT reports, MT/PT records)

Hydrostatic / pneumatic test report and pressure chart

As-built drawing and dimensional inspection report

10. Delivery & Commercial

Required delivery date / lead time constraint (specify hard deadline if applicable)

FOB point: fabricator shop / job site / other (specify)

Shipping constraints: maximum transport width / height / weight

Rigging lugs required: Yes / No — specify lift weight and rigging angle

Preservation and packaging requirements (nitrogen purge, desiccant, crating)

Owner-furnished items (OFI) to be incorporated: list any customer-supplied materials

Ready to send your RFQ to MRX?

Use this checklist to prepare your RFQ package, then submit it through our quote request form or send directly to our engineering team. The more complete your RFQ, the faster we can return a detailed proposal.